Revenue per Seat: all lessons

Lesson 2 of 3

Table turns & party mix

6 min

By the end: Compare your table sizes with the parties you actually get.

In the last lesson you saw that every empty seat-hour counts against you. Two things create empty seats: guests leaving slowly (turns) and guests arriving in sizes your tables do not fit (party mix). This lesson is about the second one, which does not show on a covers report.

Turns, defined properly

Table turns = parties seated ÷ tables in service

If 20 tables host 50 parties over a service, that is 2.5 turns. Notice what the number hides: a turn at a 6-top is not worth the same as a turn at a 2-top. Turns count parties. Revenue follows guests. The measure that ties both together is seat utilization: guests seated divided by seats available.

The mismatch problem

Guests do not book in the proportions your room was built for. Suppose most of your parties are pairs, but most of your tables are 4-tops. Every pair sitting at a 4-top leaves two seats empty for as long as they stay.

Play with it below. The room is fixed: 6 two-tops, 8 four-tops, 2 six-tops. Change who walks in and watch the seats.

Interactive

Party-mix builder

Example room: 6 two-tops, 8 four-tops, 2 six-tops (56 seats). One seating wave. Each party takes the smallest free table that fits.

93%
seat utilization
4
empty seats this wave
1
parties turned away
Source: Example simulation: one seating wave, each party takes the smallest free table that fits, no combining. The room and the starting mix are made up.

Three experiments worth running. First, push the mix toward parties of 1-2: utilization drops even though the room looks busy, because the 2-tops run out and pairs spill onto 4-tops. Second, move toward larger parties: the six-tops fill and parties are turned away while 2-tops sit idle. Third, raise the number of parties: more demand does not fix a bad mix, it just shows up as guests turned away.

Pull your own mix

Export a month of reservations and walk-in counts and bucket them: 1-2, 3-4, 5-6, 7+. Then count your tables by size. Compare the two columns as percentages. A wide gap in either direction is worth a conversation about your layout.

Example

A worked mismatch

60%
Example: share of parties that are 1-2 guests
21%
Example: share of seats that sit at 2-tops
50%
of a 4-top's seats are empty when a pair sits there
Source: Made-up example using the room from the builder above. Not a benchmark.

Ways to close the gap

  • Combinable tables. Two-tops that push into a 4 or a 6 let you match tonight's mix, not last year's.
  • Bar and counter seats for singles and pairs. They take no table inventory.
  • Booking rules. Keep 4-tops for parties of 3 or more during your busiest slots, and let pairs take 2-tops and bar seats first. Relax the rule for walk-ins and quiet slots.
  • Booking length by party size. Measure how long each party size actually stays in your room, and set booking lengths from that.
Don't solve for the rare party
A party of 7 that shows up twice a month does not justify permanent seating for 7. Handle large parties with combined tables and a rule that they book ahead. Design the room for the parties you see most.

Whatever tool holds your floor plan, keep the table sizes in it up to date, so the tables it offers online match the room your host actually has.

Check your understanding

0/3
  1. 1. A table of 4 is seated with a party of 2 for the whole night. What is the seat utilization of that table?

  2. 2. Most of your parties are 2 guests, but half your tables are 4-tops. Which change adds flexibility without replacing the room?

  3. 3. What does a table turn measure?

Finished the quiz already? Or skip it and mark this lesson done.

Put it into practice with TableShift

Your own booking page and website widget, refundable deposits paid to your own Stripe account, email reminders, a floor plan with live seating and a staff-run waitlist. The Starter plan is free.